loading

Perfect Roll Former made by PUTAI.

Suspended ceiling grid systems

Suspended ceiling systems are assembled from several interlocking steel profiles, and no single machine makes them all. PUTAI builds the complete set: T grid lines (the North American name is tee bar) for main tees and cross tees; ceiling panel, linear strip and U baffle lines for the visible panel layer; carrier and profile channel lines for the suspension frame; and compact lines for spring tees, cassette keels and related accessories. Spring tee and triangle keel are two names for the same section, just as T grid and tee bar are.
PUTAI TECHNOLOGY offers a wide range of suspended ceiling grid systems that are designed to meet the varying needs of commercial and residential spaces. Our products are constructed with precision and durability in mind, ensuring a long-lasting and reliable solution for any ceiling installation. The unique design of our grid systems allows for easy installation and maintenance, making them an ideal choice for architects, contractors, and homeowners alike. With a focus on quality and innovation, PUTAI TECHNOLOGY's suspended ceiling grid systems provide a versatile and efficient solution for any ceiling project.
Tell us the profiles you sell and the strip thickness you run. We quote against your section drawings, not against a category name.

What a suspended ceiling system is made of

Three profile families go into a standard exposed-grid ceiling.

The grid itself. Main tees run the full span and carry the weight. Cross tees, usually 600 mm or 1,200 mm modules, clip into the main tee to form the visible lattice. Both are produced on a T grid roll forming line, from galvanized or pre-painted steel strip.

The panels. Mineral fibre boards drop into the grid on most commercial jobs, but metal ceiling panels — lay-in panels, linear strips, U-shaped baffles — are formed on separate lines. These are the profiles architects specify when they want a metal finish rather than a board finish.

The accessories. Spring tees — the profile is also sold as triangle keel — hold the secondary framing. Wall angles close the gap between the grid and the wall. Ceiling hangers suspend the whole assembly from the slab above.

A ceiling factory that sells a complete system needs machines from all three groups. A factory that only supplies grid components can start with one T grid line and add panel capacity later.

The three machine groups, and which profiles each one makes

Grid machines. These produce the visible metal lattice: main tee and cross tee. Tee bar and T grid are not two products — they are two names for the same folded T-section, "tee bar" being the North American term and "T grid" the export term. The variants sold as plain type, FUT and black line differ in surface finish and edge detail, not in the machine that forms them. Face width is typically 24 mm or 32 mm, formed from narrow strip.

Panel machines. Ceiling panel lines form the flat or bevelled panels that sit in the grid. Linear strip lines form the narrow closed strips used in linear ceilings. U baffle lines form the open U-channel profiles hung vertically below the slab. A carrier line produces the heavier suspension channel that supports the panel run.

Accessory machines. Spring tee lines form the small spring steel profile that locks panels in place. The same profile is sold as triangle keel, so one line and one roller set covers both names. Cassette keel lines form the frame that holds lay-in cassette panels. A ceiling hanger machine bends wire into the hanger loop that ties the grid to the roof structure.

The important point for a buyer: these are not interchangeable. A T grid line cannot run a linear strip, and a panel line cannot produce a tee bar. Each profile needs its own roller set, and in most cases its own line.
Send your inquiry
Putai Suspension Ceiling Cassette Keel Roll Former Galvanized Ceiling Grid System Roll Forming Machine
Cassette keel is a metal keel component in ceiling systems, primarily used for dry-hanging ceiling installations. Its core function is to provide stable support for the ceiling through a system of hooks and tracks.
Putai False Ceiling Channel T Grid Making Machine Cross T Bar Roll Forming Machine
This ceiling t grid roll forming machine are specialized equipment designed to efficiently produce the metal frameworks that support suspended ceiling systems in modern construction. These machines transform raw metal coils into precise T-shaped profiles through a highly automated and continuous process.
Putai Ceiling System T Grid Tee Bar Making Roll Forming Machine
T Grid Roll Forming Machines are specialized equipment designed to efficiently produce the metal frameworks that support suspended ceiling systems in modern construction. These machines transform raw metal coils into precise T-shaped profiles through a highly automated and continuous process.
Putai Ceiling System T Grid T Bar Roll Forming Machine Production Line
Ceiling t bar making machines are specialized equipment designed to efficiently produce the metal frameworks that support suspended ceiling systems in modern construction. These machines transform raw metal coils into precise T-shaped profiles through a highly automated and continuous process.
Factory Direct Ceiling T Bar Cross T Roll Forming Machine | Putai
Introducing our high-efficiency T Grid Roll Forming Machine – engineered to transform galvanized steel or aluminum coils into flawlessly consistent T-grid ceiling components in a single pass. Designed for suspension system suppliers, contractors, and acoustic solution providers, our system delivers architectural precision, rapid installation readiness, and cost efficiency for commercial, healthcare, and cleanroom projects.
Wholesale Gearbox Transmission Ceiling T Grid Roll Forming Machine | Putai
Introducing our high-efficiency T Grid Roll Forming Machine – engineered to transform galvanized steel or aluminum coils into flawlessly consistent T-grid ceiling components in a single pass. Designed for suspension system suppliers, contractors, and acoustic solution providers, our system delivers architectural precision, rapid installation readiness, and cost efficiency for commercial, healthcare, and cleanroom projects.
Metal Roll Forming Machine Ceiling T Grid | Putai
A T-grid for a ceiling system is a type of suspended ceiling that consists of a load-bearing frame made up of metal T-shaped profiles. The Ceiling T Grid Roll Forming Machine is designed for the efficient production of T-shaped grid systems used in suspended ceiling applications.
Steel Frame Roll Forming Machine Ceiling T Grid Tee Bar Roll Former Manufacturer | PUTAI
A T-grid for a ceiling system is a type of suspended ceiling that consists of a load-bearing frame made up of metal T-shaped profiles.
Putai Suspended Ceiling T Grid Main T Cross Tee Roll Forming Machine
A T-grid for a ceiling system is a type of suspended ceiling that consists of a load-bearing frame made up of metal T-shaped profiles.
Ceiling T Grid Roll Forming Machine | PUTAI
A T-grid for a ceiling system is a type of suspended ceiling that consists of a load-bearing frame made up of metal T-shaped profiles.
Ceiling FUT T Grid Roll Forming Machine | PUTAI
A FUT T-grid for a ceiling system is a type of suspended ceiling that consists of a load-bearing frame made up of metal T-shaped profiles. These profiles are typically made of steel, aluminum or galvanized steel to offer strength and durability.
Ceiling Black Line T grid Roll Forming Machine | PUTAI
Center black line T-grid (also known as ceiling grid or suspended ceiling grid) is a type of metal frame system used to support ceiling tiles in suspended ceiling systems.

What a T grid roll forming line actually runs

The process is continuous from coil to cut length. Strip is decoiled, fed through a servo feeder, punched for the clip slots and hanger holes, roll formed through the stations, then cut to length by a flying shear while the line is still moving.

The punching stage matters more than buyers expect. A main tee needs a slot pattern that accepts cross tee clips at fixed intervals, and a cross tee needs matching end tabs. If the punch tooling is not timed to the forming speed, the module spacing drifts and the grid will not assemble on site.

For our standard T grid line, the published specification is:
Parameter Specification
Material Galvanized steel, pre-painted steel
Material thickness 0.25 – 0.50 mm
Coil width 100 – 180 mm (set to profile)
Forming stations 14 – 18
Forming speed 25 – 40 m/min, variable frequency
Main motor 7.5 kW
Hydraulic station 4.0 kW
Cutting Servo tracking hydraulic shear, ±0.5 mm
Drive Gearbox, Gear or chain
Roller material GCr15 bearing steel, HRC 58–62, hard chrome plated
Machine size Approx. 9,500 × 1,200 × 1,500 mm
Power supply 380V / 50Hz / 3-phase, other voltages on request

Thickness range is the number to check first. If you run 0.25 mm strip for cross tees and 0.50 mm for main tees on the same line, the forming stations have to be set for the lighter gauge and the drive sized for the heavier one.

Cross tee, main tee, plain type, FUT and black line

The T grid market splits by surface finish and by profile detail, not by machine type.

Plain type is the standard white or galvanized finish. Black line adds a black painted groove along the tee face, which reads as a shadow line in the finished ceiling. FUT refers to the folded-and-tucked edge detail used where the grid is exposed rather than concealed.

Main tee and cross tee differ in section height and in the punch pattern, not in the forming principle. A line set up for one can be changed to the other by swapping rollers and punch tooling, but changeover is measured in hours, not minutes. Factories that sell both usually run separate lines rather than change over twice a week.

If you are specifying a line for an export order, confirm which of these three finishes the buyer actually wants. The profile drawing differs, and a line built for plain type will not produce a black line tee without new roll tooling.

Ceiling panel, linear strip and U baffle

These three are often quoted as one group, but they behave differently on site.

Ceiling panel lines form lay-in panels — flat, bevelled or stepped edge — in widths that match the grid module. The edge detail is what holds the panel in the tee, so the forming tolerance at the edge is tighter than the panel face.

Linear strip lines form narrow closed strips, usually 100 to 300 mm wide, that clip together to make a continuous linear ceiling. The strip carries its own joint, so the forming line has to produce a consistent interlocking edge along the full coil length.

U baffle lines form the open U profile hung vertically below the slab. Because the baffle is visible from both sides, surface finish and edge straightness matter more than for a concealed profile.

All three run the same basic sequence — decoil, feed, punch, form, cut — but the roller sets and the punch tooling are dedicated to each profile.

Spring tee, cassette keel and the accessory profiles

The accessory profiles are small, but they decide whether the system assembles cleanly.

Spring tee is the spring steel profile that clips the panel edge and lets the panel be removed without dismantling the grid. Its section is triangular, which is why the same product is also sold as triangle keel — one profile, two names, one roller set. Buyers who ask for "triangle keel" and buyers who ask for "spring tee" are ordering the same line; the only thing worth confirming is the section drawing.

Cassette keel is a different profile: the frame that holds lay-in cassette panels flush with the grid face.

These lines run narrow strip at lower tonnage than a main tee line, and the forming stations are shorter. The critical specification is the spring temper of the steel — a spring tee formed from the wrong temper will not hold its clip force after installation.

Most ceiling factories buy one accessory line and run several profiles on it with interchangeable roller sets, because order volumes for any single accessory profile are small.

FAQ

1. Can one line produce both main tee and cross tee?
Yes, with different roller sets and punch tooling. The changeover takes hours, so most factories running both at volume use two lines.

2. What is the difference between a T grid machine and a tee bar machine?
None. Tee bar and T grid are two names for the same folded T-section — "tee bar" is the more common term in North America, "T grid" in export markets. The machine specification is identical, and one line serves both names.

3. Do you supply the punch tooling for the clip slots?
Yes. Punch tooling is built to the buyer's profile drawing, because slot spacing differs between grid systems.

4. What steel temper is needed for spring tees?
The profile has to hold clip force after forming, so the strip must be ordered to a spring temper specification rather than standard commercial temper. Confirm the grade with your coil supplier before the line is built.

5. Can the line run pre-painted steel?
Yes, both galvanized and pre-painted strip run on the same line. Pre-painted strip needs the rollers to be chrome plated and the feed rolls to be non-marking, which is standard on our configuration.
Ready to work with us ?

Tianjin Putai Technology

Contact Us
Copyright © 2026 Tianjin Putai Technology Co.,Ltd | Sitemap | Privacy Policy
Customer service